softpedia copypast

Philips model 42pfl3704d/f7.Philips 42PFL3704D/F7 Service Manual

By admin on July 15, 2021 0 Comments

 

Philips model 42pfl3704d/f7.Philips 42″ 1080p LCD HDTV

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Are you an E-Blast Insider?.Philips 42PFLD Specs – CNET

 

Philips 42PFLD/F7 lcd television parts – manufacturer-approved parts for a proper fit every time! We also have installation guides, diagrams and manuals to help you along the way! Philips 42PFLD overview and full product specs on CNET. Philips 42PFLD | 42PFLD/F7. Post a comment. Model 42PFLD. This unique Philips technology brings motion sharpness of LCD displays to an unprecedented level. 4 HDMI inputs with Easylink for a full HD connection. EasyLink uses the HDMI CEC industry standard protocol to share functionality between connected devices and the TV. With Easylink only one remote control is needed to operate main functionalities Brand: Philips.

 

Philips model 42pfl3704d/f7.PHILIPS 42PFLD/F7 SERVICE MANUAL Pdf Download | ManualsLib

This unique Philips technology brings motion sharpness of LCD displays to an unprecedented level. 4 HDMI inputs with Easylink for a full HD connection. EasyLink uses the HDMI CEC industry standard protocol to share functionality between connected devices and the TV. With Easylink only one remote control is needed to operate main functionalities Brand: Philips. Philips 42PFLD/F7 lcd television parts – manufacturer-approved parts for a proper fit every time! We also have installation guides, diagrams and manuals to help you along the way! Philips 42PFLD overview and full product specs on CNET. Philips 42PFLD | 42PFLD/F7. Post a comment. Model 42PFLD.
 
 
related:
Model #42PFL3704D/F7 Philips lcd television
Warranty & Returns
Philips 42″ p LCD HDTV –
Philips 42PFL3704D Specs
Add accessories
LCD TV 42PFLD/F7 | Philips

Table Of Contents. Quick Links. See also: User Manual. Service Manual 42″. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto. Information in this document is subject to change without notice. Funai reserves the right to change the content. All other trademarks used herein remain the exclusive property of.

Nothing contained in this manual should be construed as granting, by implication or. Misuse of any trademarks or any. Funai shall aggressively enforce its intellectual property rights. Table of Contents. Previous Page. Next Page. Philips lcd tv 42pfl cm 42″ full hd p with digital crystal clear 33 pages. Philips flat tv 32pf 32″ lcd hd ready with pixel plus pages.

Philips professional flat tv 23hf 23″ lcd 22 pages. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Some of these service special tools should be used when and as recommended.

Synchronizing Sens. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. Page 6 3. Design Alteration Warning – Do not alter or add 7. Product Safety Notice – Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio Page 7 Precautions during Servicing A.

Parts identified by the symbol are critical for safety. Replace only with part number specified. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration.

Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. Page 10 3.

Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC. Page 11 With Iron Wire: 2. Installation 1.

Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC.

When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily. Page 12 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

Part Fig. When reassembling, follow the Desolder steps in reverse order. Page 14 3 Fig. D2 A91H2DC D3 A91H2DC D4 A91H2DC Page 20 Note: desoldered. D2 A91H5DC D3 A91H5DC D4 A91H5DC Page 26 Note: desoldered. D2 A91H9DC D3 A91H9DC D4 A91H9DC Use the service remote control unit. It is important to perform 2. Page 32 1. Purity Check Mode 2. Point green, blue, and white to check for non-active pixels. Enter the Service mode. Screen buttons 2. Each time pressing [7] button on the service M.

Page White Balance Adjustment The white balance adjustment should be 5. Blue Cutoff adjustment. The customer will be prompted to select a language and program channels after the set has been initialized. Appearance State a. USB memory Downloading the firmware from b. Remote Control Unit Downloading Writing the downloaded firmware Writing Firmware Update Procedure in flash memory.

Is the fuse F normal? Check C, D, D and their periphery circuit, and service it if defective. Check D and their periphery circuit, and service it if defective. Replace Q Check the line between video input terminal and each pin of IC Check SP,SP and their periphery circuit, and service it if defective.

These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. The voltage for parts in hot circuit is measured using Also, in order to have the ability to increase the input slowly, hot GND as a common terminal. Fixed voltage or Auto voltage selectable power supply circuit is used in this unit.

Shown in Schematic Diagram. Numbers are not in sequence. Description Part No. Page 91 Ref. Page 92 Ref. Page 93 Ref. Page 95 Ref. Page 96 Ref. Page 97 Ref. Page 99 Ref. Page Ref. Print page 1 Print document pages. Cancel Delete. Sign In OR. Don’t have an account?

Comments are closed.